Sep 9, 2020

Posted by | Comments Off on Pickup truck hitch in Boise Idaho- Points to Remember

Pickup truck hitch in Boise Idaho- Points to Remember

Using fifth wheel hitches helps you tow heavy loads than when using other types of hitches. They also ensure more stability when towing. A fifth wheel pin box can be found on many commercial and travel trailers. A fifth wheel pin is connected to an already installed hitch during towing in most trailers. The hitch is installed in the trucks rear frame or at the bed. A hitch installed on a truck is the only requirement when towing a fifth wheel trailer. Hooking up of a fifth trailer can be done in easy steps.Feel free to find more information at pickup truck hitch.

You need a truck already installed with a fifth wheel hitch, a trailer equipped with the fifth wheel pin box, wheel chocks and white lithium grease.

The trucks tailgate lowered use the white lithium grease to grease the receiver hitch, the skid plate and the trailer king pin.

-Next, release the pin or clip that is locking the hitch. Confirm that the hitch is operating properly by pulling the hitch release arm. Use wheel chocks to chock the wheel on the trailer.

-Back up your truck. This should be done slowly and carefully. Make sure that the trailer king pin is situated behind the skid plate of the fifth wheel hitch. The trailer king pin should glide into the skid plate. For this to happen, lower or raise the landing gear of the trailer, till the king pin slides inside. Make sure the trailer is not lifted. To make sure the hitch jaws get closed, the truck should be backed up. When the hitch release handle closes, the hitch jaw is closed.

-Confirm the closing of the hitch jaws. This can be done by looking at the hitch’s back. If the jaws have not closed, the truck should be pulled forward. The landing gear should be raised or lowered and reconnected till the king pin is captured fully by the hitch.

-To check whether the hitch is fully engaged, the trailers landing gear should be raised a little off the ground. The truck should then be placed in drive gear and the connected trailer should be pulled shortly by the truck. The trailer will disconnect if the hitch has not been engaged fully. The connection procedure should be repeated till the hitch gets fully engaged.

-To prevent the arm from releasing the trailer by opening up, clip the hitch arm in place. The trailer lights should be connected and the landing gear should be raised. Next, the wheel chocks should be removed and the tailgate closed. Test the brakes on the trailer by using the override brake control manual.

Read More
Sep 9, 2020

Posted by | Comments Off on Pickup truck hitch: Secrets Revealed

Pickup truck hitch: Secrets Revealed

Whether you are pulling a pleasure boat, a horse trailer or a pop-up camper, the right hitch can make all the difference. Having the right hitch in place means increased safety for your tow vehicle and your trailer, easier pulling and less stress and strain on your truck. Choosing the right hitch is not difficult, but it is important to consider your needs carefully.

Before you go shopping for a trailer hitch, first take a good look at the trailer you plan to haul. You should be able to find the weight of the trailer when empty by looking at the manual that came with the vehicle. Do not forget to add the weight of what you will be hauling when you shop for a hitch. The average horse can weigh up to 1,000 pounds, so if you plan to haul a two horse trailer you will need to add a full ton to the needed weight capacity when you choose your receiver hitch.

If the total weight of your trailer is less than 2,000 pounds and the tongue weight is less than 200 pounds, a class I trailer hitch should be all you need to pull that trailer safely. You can find the tongue weight as well as the trailer weight in your owner manual.

You need a class II hitch if your trailer weighs up to 3,500 and has a tongue weight of up to 300 pounds. A class II trailer hitch should be sufficient to pull a small boat, a snowmobile trailer or a camper.

You need a larger draw bar hitch to handle trailer weights of up to 5,000 pounds, with a tongue weight of up to 300 pounds. It is important to check the weight of the trailer before you go shopping for a hitch, and it is just as important to consider your future needs when you choose a hitch for your vehicle. If you think you might upgrade to a larger boat down the road, buying a larger hitch for your vehicle is a smart move. A larger hitch will give you move flexibility, no matter what you plan to haul.

Read More